您好,欢迎访问优校网! 收藏本页 手机访问
今天是:

shaft end是什么意思


中文翻译轴端

网络释义

1)shaft end,轴端2)end axle,端轴3)tail-end,尾轴端,尾端4)end journal bearing,端轴颈轴承5)stirring axial terminal,搅拌轴端6)roll end sleeve,辊端轴套

用法例句

    New structure of shaft end fixture;

    一种轴端处紧固联接的新结构

    It is suggested that the vertical stiffness of the mid-axle should be lower than the end axle.

    分析了铁路进一步提速对机车牵引动力的要求,从改善机车在既有线路运行时的动力学性能及曲线通过性能出发,对200km/h机车(C0-C0轴式)一系簧有关刚度进行分析计算,认为应使中间轴一系簧垂向刚度小于端轴。

    The failure of 40 Cr steel end axle is analyzed by metallographic examination,chemical analysis and mechanical testing.

    采用光学显微镜分析、化学成分分析和力学性能试验,对40Cr钢端轴断裂件进行分析。

    According to the heat treatment process requirement for the profile control technology of roll end sleeve developed by CLECM Co.

    根据法国CLECM公司板形控制技术中辊端轴套的热处理技术条件 ,研究了 18NcD6钢的渗碳淬火工艺、热处理畸变控制及其力学性能 ,成功地实现了新型辊端轴套的国产化 ,产品性能完全达到法国CLECM公司技术标准 ,收到了显著的经济效

    Drilling machines-Spindle noses

    GB/T2815-1989钻床主轴端

    Dimensions of spindle ends for manually operated electronic components

    GB/T2775-1993手控电子元件的轴端尺寸

    distance from spindle nose to central line of table

    轴端面至工作台中心线距离

    Lock rings at the end of shaft with scre

    GB/T891-1986螺钉紧固轴端挡圈

    Lock rings at the end of shaft with bolt

    GB/T892-1986螺栓紧固轴端挡圈

    hub cap for road motor vehicles or tractors

    轴端盖,道路机动车辆或摩托车用

    Remove vibration damper bolt and washer from end of crankshaft.

    从曲轴端拆下减震器螺栓和垫圈。

    Retrofit of the Low-pressure Shaft Butt Seal in 51-50-3 Type Steam Turbine

    51-50-3型汽轮机低压轴端汽封的改造

    fan end thrust ball bearing

    风扇端止推滚球轴承

    axial double mechanical seal

    轴向双端面机械密封

    SMALLER DIAMETER OF PIVOT BEARING

    轮毂轴承的较小直径端

    End play in drive pinion bearings.

    驱动小齿轮轴承的端隙。

    vertical -spindle double ended grinding mahcine for piston ring

    活塞环立轴双端面磨床

    horizontal spindle double ended grinding machine for piston ring

    活塞环卧轴双端面磨床

    Pressure-compensated air bearings are used on both ends of the trunnion axis.

    耳轴两端各用一压力补偿空气轴承。

    Measures for improving the concentricity of the bearing s minor hole at the two ends;

    提高套筒两端轴承档内孔同轴度的措施

    The dates you specified for the axis values can't be used, because the maximum axis value must occur at a later date than the minimum axis value.

    为坐标轴指定的日期非法。坐标轴远端的日期必须晚于近端的日期。

    Either extremity of an axis through a sphere.

    (轴的)两极穿过一个球体的中轴的两端中的任一端