A new method of the design for tie bar and falsework during the construction of the thin-wall of bridges;
薄壁墙施工中拉杆与脚手架设计的新方法
Study on the Dowel and Tie Bar in Jointed Plain Concrete Pavement;
普通水泥路面传力杆及拉杆研究
In order to overcome the problem of early failure of the tie bar in the plastics injection molding machine, an integrated finite element analytic model was formulated dealing with the tie bars,fixed platen, movable platen, and rear platen.
针对注塑机拉杆的早期断裂问题,为使拉杆应力分布合理化,以拉杆与定模板、动模板和调模板等组成的整体有限元分析模型为基础,用优化方法研究拉杆卸载槽的合理位置以及各模板基本厚度的确定,以及拉杆卸载槽的位置和各模板基本厚度对拉杆应力分布的影响。
The Analysis and Solution of Process Plan for the Batch Production of Tie Rod;
拉杆批量生产工艺方案的分析与确定
After some analyses of load transfer behavior of anchor rod,and based on the results of field test,a type of technique of removable anchor for which the pull rod can be removed,is proposed.
通过对锚杆荷载传递特性的分析和在现场原型试验研究的基础上,提出了一种仅拆除拉杆材料的可拆型锚杆技术。
Several improvements have been made after analyzing the causes of frequent fracture for pull rod in roughing mill stand at Steel Bar Plant with 3D modeling software Pro/E and finite element analysis software ANSYS .
采用三维建模软件Pro/E和有限元分析软件ansys,对棒材厂粗轧机架拉杆频繁断裂的原因进行分析,并做了有效的改进。
A calculation method of action effect increment of prestressed horizontal tension rod;
预应力水平拉杆作用效应增量的计算
The cause analysis on the tension rod rupture of the coal pulverizer and welding repair
磨煤机拉杆断裂原因分析及焊接修复
The structural performance of beam string structures changes greatly,when cables are replaced by prestressed tension rods.
在张弦梁中用预应力拉杆代替拉索,其结构性能发生变化;通过分析比较得出预应力拉杆式张弦梁的性能特点和设计中应当注意的事项。
Finite element analysis of tie-bars and platens of a plastic injection machine;
注塑机拉杆与模板的有限元分析
Stress analysis & parameters optimization of slot for releasing stress of a tie-bar of an injection machine;
注塑机拉杆卸载槽的应力分析与优化
On the basis of briefly analyzing the mechanical model of toggle clamping mechanism,taking the minimum sum of both tie-bar and toggle s weight as the target function,taking stiffness condition as the constraint condition,the paper calculates the tie-bar diameter with optimal design.
在简要分析肘杆式合模机构的力学模型的基础上,以拉杆、肘杆质量之和最小作为目标函数,将刚度作为约束条件,用优化设计的方法对拉杆直径的计算进行了研究。
tightening bolt
拉紧螺栓,(铁)风口拉杆
top link adjustment
(悬挂机构的) 上拉杆调节
emergency support
车底制动拉杆安全托
hood hinge rod bracket
机罩的铰链拉杆支架
extensible link servo
可伸缩拉杆伺服机构
steering drag link rear end grease fitting
转向纵拉杆后端油嘴
steering knuckle tie rod end pressure lubricator
转向节横拉杆接头油嘴
Front cable not secured to lever
前钢索不确保连到拉杆
level(l) ing box
悬挂装置斜拉杆调节器
Remove the nut and bolt attaching the track bar to the track bar mount on the body of the vehiclRemove the track bar from the track bar mount.
拆卸接合横拉杆与位于车身之横拉杆固定座的螺帽与螺栓。将横拉杆自横拉杆固定座拆卸下来。
LOWER TRACK BAR BOLT INSTALLATION
下横拉杆螺栓的安装
Failure Analysis of 30Cr2Ni2Mo Rod
30Cr2Ni2Mo拉杆断裂失效分析
Strut-and-tie Model of Deep Beam Design Under Uniform Distributed Loads
均布荷载下深梁设计的压杆-拉杆模型
Position lever assembly on floorpan and install lever mounting bolts.
将拉杆组合放置到底板上并安装拉杆固定螺栓。
Design of Reinforced Concrete Deep Beam Based on Strut-and-tie Model;
钢筋混凝土深梁基于压杆—拉杆模型的设计
The track bar connects the rear axle to the frame/body of the vehiclThe track bar is isolated from the body of the vehicle by an isloator bushing located in each end of the track bar.
横拉杆把后轴联结到车框或车体上。横拉杆用一安放在横拉杆两端的隔离衬套与车体隔离开。
steering knuckle tie rod end assy
转向关节横拉杆接头总成; 转向节横拉杆接头总成
The linkage may consist of a series of interconnected levers and rods, or levers and a cable.
相连部分由一系列相关的拉杆和轴或拉杆和链索所组成。
本网站所收集内容来自网友分享仅供参考,实际请以各学校实际公布信息为主!内容侵权及错误投诉:1553292129@qq.com
CopyRight © 2020-2024 优校网[www.youxiaow.com]版权所有 All Rights Reserved. ICP备案号:浙ICP备2024058711号