superdeep drilling是什么意思

网络释义

用法例句

1 exploration area as an example,introduced quality control measures of ultra-deep borehole: ① on prevention of deviation,requiring derrick foursquare installation,selecting suitable drilling parameters,using drill collar pressuring,non-bending drilling tools,surveying inclination every 200 meters;② on co.

以磁西一号勘探区37-3孔为例,介绍了超深钻孔的的质量控制措施,指出了在孔斜预防方面,要求钻塔安装稳固,选择适宜的钻进参数,采用钻铤加压,保持钻具不弯曲,每200m进行测斜一次;在岩心采取方面,使用双管取心和岩心提断器进行取心,钻时控制在2。

Construction Technology for the Ultra-large and Ultra-deep Cast-in-place Bored Pile Testing Pile of Jiashao Bridge

嘉绍大桥超大超深钻孔灌注桩试验桩施工技术

Construction of 90 m Super Deep Bored Pile and Post-Grouting of Bottom Pile

90m超深钻孔灌注桩及其桩端后注浆的施工

Drilling 50 yards deep,

钻孔至50码深处，

Technique for Construction of Large Diameter Over-long Drilled Piles in Complex Geology in Deep Water

深水复杂地质大直径超长钻孔桩施工技术

Key Construction Technique for Super-long and Large-diameter Bored Pile

深水超长大直径钻孔灌注桩施工关键技术研究

Since the inception of this project in1998, three pre-pilot holes have been completed and the main hole has reached a depth of over3500 m.

从98年开始，已经完成3个预先导孔的钻探工作，主孔钻进深度已经超过3500米。

guide twist drill

有导径的深孔麻花钻

APPLICATION OF DUPLEX REINFORCED CONCRETE BORING CAST-IN-PLACE PILE ON LARGE-SCALE DEEP EXCAVATION SUPPORT

双排钢筋混凝土钻孔灌注桩在大面积超深基坑支护中的应用

Application of Wireline Core Drilling in Coalfield Ultra Deep Boreholes

绳索取心钻进技术在煤田勘探超深孔施工中的应用

Study on drill bit for large diameter core drilling of deep hole in hard rock

硬岩深孔大口径取芯钻进的钻头研究

Design and Realization of the Monitoring System in Deep-Sea Drilling Machine

深海中深孔钻机监控系统设计与实现

The first choice is to dig our heads and oil drills deeper into the ground.

第1种选择就是用石油钻孔机钻至更深的地底。

Supporting the use of impact drilling electric drill. Drilling, hole spacing with hole depth should meet the design requirements.

（1）钻孔使用配套冲击电钻.钻孔时,孔洞间距与孔洞深度应满足设计要求.

high efficiency drilling system for small and deep hole

高效小直径深孔钻削系统

STEP HOLE DRILLING METHOD FOR MEASURING PLANE RESIDUAL STRESSES IN DEEP LAYER

钻阶梯形孔法测量深层平面残余应力

Study on High Speed Drilling in Deep 38CrMoAl Steel Tube;

38CrMoAl料筒高速深孔钻进研究

The CAD and research of drill bit escape of clips for the deep hole processing drill

深孔加工钻头排屑研究及CAD设计

Stability and Bifurcation of the Drilling Shaft System in Processing Deep Hole Based on Boring and Trepanning Association

BTA深孔加工钻杆系统的稳定性及分岔