您好,欢迎访问优校网! 收藏本页 手机访问
今天是:

cone seat (for retaining nut)是什么意思


中文翻译锥型座(螺帽定位用)

网络释义

1)cone seat (for retaining nut),锥型座(螺帽定位用)2)set stud,定位螺锥3)tapper tap,螺帽丝锥4)tapered cup nut,锥形螺帽5)lock nut bearing,锁紧螺帽座6)hold-down nut,retaining nut; fixing nut,固定螺帽

用法例句

    BRACKET MOUNTING NUTS

    支架固定螺帽(2)

    EVAP Canister Mounting Nuts (canister-to-mounting bracket)

    EVAP罐固定螺帽(罐到固定支架)

    Remove the four viscous fan/drive assembly mounting nuts from the water pump studs and remove viscous fan assembly.

    从水泵螺椿上拆下四个粘性风扇/驱动组合的固定螺帽并拆卸粘性风扇组合。

    except the screws and nuts that held the knocker.

    只有固定门环的螺丝和螺帽。

    These nuts and bolts hold the wheels on.

    这些螺帽和螺栓把轮子固定住了.

    Remove hinge retaining nuts from studs.

    从双头螺栓拆下固定铰链的螺帽。

    These bolts and nuts hold the wheels on.

    这些螺栓和螺帽把轮子固定下为。

    Install the forward nut attaching the handle to the door.

    安装把车门手柄固定在车门上的前向螺帽。

    Remove nuts attaching GOP to support bracket.

    拆下把风栅口面板固定在支架上的螺帽。

    reverse anchor jam nut

    反向锁闭机构紧固螺帽

    Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts.

    在轴壳内(没有垫片)安装差速箱和模型轴承,并紧固固定帽螺栓。

    Remove the nut and bolt attaching the track bar to the track bar mount on the body of the vehiclRemove the track bar from the track bar mount.

    拆卸接合横拉杆与位于车身之横拉杆固定座的螺帽与螺栓。将横拉杆自横拉杆固定座拆卸下来。

    Fuel Pump Module Locknut

    燃油泵模组锁定螺帽

    fixed pitch propeller

    定螺距螺旋桨固定螺距螺旋桨

    "Bolts,screws & nuts"

    "螺栓,螺丝及螺帽"

    Mounting Bolts (Screws)—IAC Motor

    固定螺栓(螺丝)—IAC马达。

    Turn the wiper module over and remove the nut that secures the wiper motor crank arm to the wiper motor output shaft.

    转动雨刷模组盖,并拆下将雨刷马达曲柄臂固定于雨刷马达输出轴上的螺帽。

    Using a short piece of pipe and Holder 6958 to hold the pinion yoke, or pinion flange, remove the pinion nut and washer.

    用短管和托架6958固定小齿轮轴轭或小齿轮凸缘,拆下小齿轮螺帽和垫圈。