oil keeper是什么意思

网络释义

用法例句

The present status abroad,domestic level and its application of filmatic bearing oil were described.

介绍了油膜轴承油国外现状和国内水平及其应用简况，分析了油膜轴承用油国产化的人为障碍及今后国产化的希望。

The performances and the results of service test of 460 filmatic bearing oil used for morgan type no-twist wire rod mills at high speed were presented.

介绍了摩根型无扭高速线材连轧机用４６０号油膜轴承油的性能及工业使用试验结果。

The formulation of 220 anti-wear type filmatic bearing oil was described, and the package's formulation was determined.

介绍了220抗磨型油膜轴承油的研制经过，确定了复合添加剂配方，研制的油品性能与MobilVacuoline533和ShellVitreaM220油相当。

Lanzhou refinery produced 100# abrasion resistant oil film bearing oil is suitable for lubrication of the circulation system of the high speed wire rolling machine package.

兰炼100号抗磨型油膜轴承油用于高速线材精轧机组循环系统的润滑,满足高温、多尘、有冲击负荷及与水接触等苛刻工况的要求,具有优越的分水性、抗磨性、氧化安定性、防锈性、水解安定性、抗泡性、过滤性以及与进口油品的混兑性,在天津钢铁厂高线分厂取得良好的应用效果。

Study on contact damage of sleeve of oil-film bearing in rolling mill;

大型轧机油膜轴承锥套损伤问题研究

The Oil-film Temperature Fild Analysis of Oil-film Bearing Based on ANSYS;

基于ANSYS的油膜轴承油膜温度场分析

This paper presented the mechanism of fretting fatigue failure that happened on the contact surfaces between sleeve and roll neck of oil-film bearing under the rolling load.

研究了油膜轴承锥套与辊颈接触表面在轧制载荷作用下发生微动疲劳损伤的力学机理。

Design and analysis of structural parameters for capillary oil film bearing

毛细管节流的油膜轴承结构参数设计分析

A modern large-scale mill's perfect bearing——oil film bearing,a key part of the mill,has many advantages,such as large carrying capacity,long service life,wide speed range,low friction coefficient,small configuration size,strong impact resistance,etc.

现代大型轧机的理想轴承——油膜轴承是轧机的关键部件,具有承载能力大、使用寿命长、速度范围广、摩擦因数小、结构尺寸小、抗冲击能力强等优点。

Baosteel Branch's 5m mill is the first especially wide and heavy plate production line,and oil film bearing is one part of its main equipment.

宝钢分公司厚板厂5m轧机是国内第一条特宽幅厚板生产线,油膜轴承是厚板轧机的主要设备之一,正确认识和掌握其特点是提高厚板生产的关键环节。

The partially alloyed CuSn10 powder for high speed,low noise and self lubricating bearingshad been successfully developed by Cu Sn alloying process The characteristics of powders were investigated by SEM The influence of powder mixing process,green density,diffusion time and temperature on the properties of powders were discusse

本文通过对电解Cu粉、雾化Sn粉的部分合金化过程的研究 ,制备出适于制造高速、低噪音、微型含油轴承的CuSn1 0部分合金化粉末。

Application of Filmatic Bearing Oil on High-speed Rod-rolling Mill

油膜轴承油在高速线材轧机上的应用

Shaft Assembly (Male, female, washer, grease….

轴组件（轴，轴套，轴承，油脂。。。）

General technical requirement of oil film bearing for rolling mill

GB/T13345-1992轧机油膜轴承通用技术条件

Static Testing Investigation of Controllable Hydrodynamic Bearing with Gaint Magnitostrictive Actuator

GMA可控油膜轴承的静态试验研究

Analysis on Measurement Approach for Lubricant Film Thickness of Sliding Bearing

滑动轴承润滑油膜厚度测量方法分析

The Research on Oil Film Rupture Regular of Novel Spiral Oil Wedge Hybrid Journal Bearing

新型螺旋油楔动静压轴承油膜破裂规律的研究

groove-cutting chisel

槽刨, 油槽铲(轴承)

Calculation of the influences of marine shafting dynamic alignment affected by bearing oil film

船舶轴系动态校中轴承油膜的影响计算

Influence of misaligned journal bearings on the start-up process of tandem cold rolling mills

油膜轴承倾斜承载对冷连轧机启动的影响

A Study on the Seal of HAGC Cylinder and Oil Film Bearing of Backup Roll

HAGC油缸和支承辊油膜轴承用密封件的国产化研究

emergency bearing oil pump

紧急备用轴承油泵应急轴承油泵

"To minimize friction, the contacting surfaces in a Bearing may be separated by a film of oil or gas, these are also sliding Bearings ."

为了减小摩擦力,轴承内的两个接触面可以用一层油膜或气膜隔开,这类轴承称作滑动轴承。

Design and Accomplish of Visual Performance Calculation System of Oil-film Bearing

油膜轴承可视化性能计算系统的设计及实现

Study on Oil Film-Roller Combination Bearing of φ200 Cantilever Finishing Mill;

φ200悬臂式精轧机油膜—滚子组合轴承开发研究

Development of Journal Bearing Test Equipment and Measurement of Oil Film Pressure;

滑动轴承试验装置开发与油膜压力测量

Error Analysis of the Nonlinear Oil Film Forcein Thrust Bearings;

一维滑块推力轴承高阶非线性油膜力误差分析

To Keep Technological Superiority Is the Base of Continuous Development of Taizhong Oil Film Bearing;

保持技术优势是太重油膜轴承持续发展的根本

Analysis and research of the breaking of the thick plate rolling mill oil taper sleeve

特厚板轧机油膜轴承锥套断裂原因分析与研究